6 press lock button once. Page 6 62816 / 01 troubleshooting:
unique wedding registry idea safe hands free door lock
No user code programmed program at least one user code ©2014 weiser corporation important safeguards 1 2 3 remove battery pack.
How to change code on door lock weiser. On the touchpad, select the settings app from the home screen. Remove the existing door lock. Pair with smartthings [found information on how to put the lock into pairing mode by following [ref 4] pairing the smart door lock with your touchpad”]
Reference guide exterior back panel. Install the smart door lock using the manufacturer’s installation guide provided in the box. To start over, touch the lock button to lock the door.
Keep holding the button for 30 seconds until the lock beeps The door can be locked with the lock button, but the user code will not unlock the door. This is something most homeowners quite often forget to do.
Enter user code to be deleted. Fl ash fi ve times and you will hear fi ve beeps. Insert the key into the lock and turn it slightly more than half a turn while pulling the cylinder tailpiece through the back of the lock.
If the door still won’t unlock, use a key to unlock the door. The full screen is now revealed. Hold these two units in place, then insert screws into the interior side of the lock to fasten it to the door.
Press and hold the program button until the keypad 4. Page 5 62812 / 01 deleting a single user code with the mastercode enabled 1. Manufacturer’s installation guide important installation steps 1.
Using the weiser app within bluetooth range, you can lock/unlock the aura smart lock and program up to 250 user access codes that can be scheduled and. Door drilling instructions available at www.weiserlock.com/doorprep. Wait a moment for the three lights and three beeps to repeat.
If it does not unlock, repeat steps (a) through (c). Enter the access code to unlock: Enter in 4 to 8 digit code onto the keypad.
The door is now unlocked! 2 press lock button once. Press the 1 button and wait for the same three lights and three beeps.
If you're looking for answers, information and resources to help. If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock. Enter in 4 to 8 digit code onto the keypad.
Enter the code to unlock: Test the old user code to make sure it can no longer unlock the door. This process will only work if your weiser lock is installed on the door and the door is shut.
When the led flashes green, the lock has been reset. If your old code still remains in the unit, you will need to perform a hard reset of the unit. Man installing a door lock on a white door.
Press and hold the program button while reinserting the battery pack. Fl ashes green (about 5 seconds). For instuctions on how to add user codes when the mastercode is disabled, see the installation and user guide that came with your lock.
Prepare the door and check dimensions. Locked turnbutton the turnbutton cannot rotate. Smartcode at a glance deleting a single user code
Make sure the user code is correct and that the lock button is pushed after entering the user code. Door jammed while attempting to lock relock door. After typing in the last 4 digits of your phone number click change lock code and type in the new lock code you would like.
38 mm (1 1/2 in). For example, if you want to delete the third code, add a diff erent user code in position three. Press the program button once more.
Press the program button twice, enter the same or a new code and then press the lock button once. Just go through all the possible combinations and unlock it (only if its a 3/4 digit) on the other hand if you do know the code and want to change the lock, hold down the unlock button/lever and change the digits and that should change the code. If you have an old weiser lock that does not have the smart key feature, you'll have to remove the lock from the door to rekey it.
Code to teach the lock the orientation of the door: Just pull off the top back cover of the unit and you will find the simple step by step instructions on how to change the combination on the inside of the cover. 4 press lock button once.
Press the “lock” button to save code. Procedure continued on next page 4 / 15 62810 / 01 usa: Insert the exterior (keyed) side of the lock through the exterior side of your door.
The door is either 54 mm (2 1/8 in) or. Programming the 2nd user code. Call technical support for further troubleshooting.
You should see the schlage button turn green, giving one long flash and one long beep. Consequently, how do you change the code on a kwikset door lock? Smart door lock (weiser smartcode 10 touchpad electronic deadbolt) 2.
Pair the smart door lock to your rogers smart home monitoring system using this guide. Find all the resources to help with your weiser product and installation needs. If unsuccessful make sure to enter the same valid code in steps 3 and 5.
Test code while the door is open, test the user code to make sure it no longer unlocks the door. The bolt should retract to the unlocked position. Press the program button once.
Once the smart door lock has been physically installed and tested for proper functioning, follow the steps below to pair your smart door lock with your rogers smart home monitoring system. Line up the connecting rods and cylinder tailpiece to insert the interior trim. Measure to con irm that the hole in.
The lock beeps, the keypad fl ashes red, and the door cannot lock or unlock. Press the program button on the interior unit three times. If drilling a new door, use the supplied template and the complete.
With auto lock enabled, smartcode will automatically relock the door Please install one smart door lock at a time. Hope this helps, i'd been wondering about it myself for a lonnngg time :)
Press the “lock” button to save code. Switch #2 enables the auto lock when in the on position. 3 enter user code to be deleted.
When the door is closed and the lock.
Code Handle Keyless Lockset Keypad Door handles modern
Kwikset SmartCode SmartKey Bronze SingleCylinder